Contact Us

  • Celtic Sustainables
  • 01239 777009
  • Unit 3 Parc Teifi Cardigan Ceredigion SA43 1EW

Information

About us

Put something nice about your company here...

Skip to main content
Free delivery icon
Free delivery icon
Free delivery icon

DAB Divertron 900X with 1m Floating Intake

DAB

£519.95

Prices Include VAT

SKU:
IR10137
£519.95

Prices Include VAT

Adding to cart… The item has been added

PowerDiver: DAB Divertron 900 X submersible pump with 1m Floating Intake

Ideal for pumping rainwater from above-ground or underground rainwater tanks. Install in the tank and pump the water from the cleanest part of the tank.

The DAB Divertron 900X also known as a Leader Divertron 900X is a high quality multi-stage DAB submersible pump with 3 impellers and electronic flow control (i.e. the pump will automatically pump on demand). We have teamed it here with a 1m Floating Intake so the water that is pumped is always taken from the cleanest part of a water tank. This reduces the potential for clogging up the pump.

Ideal for:

  • Domestic water boosting
  • Rainwater harvesting
  • Surface irrigation
  • Tank to tank transfer (see also QuickStop Valves to save energy and pump wear)
  • Above ground tanks
  • Garden water butt
  • Submersed surface and underground installation.
  • Can also be purchased without the Floating Intake, see separate listing DAB Divertron 900X.

Floating Intake

In your rain water collection tank or water holding tank, debris will either float to the surface of the water (where it is lighter than water - oil, pollen etc) or sink to the bottom of the tank.

A Floating Intake Filter allows the water to be collected at a minimum distance of approximately 6" (150mm) below the surface of the water - where the cleanest water is. This prevents any floating debris to enter the pump suction hose and unlike other pump suction filters it does not fall to the bottom of the tank (where much of the debris lies).

DAB Divertron 900X

The electronic flow control of the DAB Divertron 900 pump responds to the pressure in the outlet delivery pipe. As the user draws water by opening a tap or similar, the pump starts automatically. When you turn the water demand off, the pump cuts out automatically. It is manufactured with anti-corrosive and rust-proof materials. The motor has thermal overload protection and has 1" threaded outlet and intake. The pump has a diameter of just 160mm.

The Divertron 900 X DAB submersible pump has a wear resistant shaft, and the excellent water-cooling of the motor allows the pump to operate when fully submerged. Being cooled by the waterbody that the pump is immersed it is quiet in operation.

This is an upgraded version of the Divertron 1200X. Improvements include improved performance, lower power consumption and an accessible Capacitor. This new version consumes 30% less power than the previous model while still achieving higher performance. This is in line with European Directives for the Minimum Hydraulic Efficiency Index (MEI) for pumping equipment, which will come into force in 2024. Lower power usage helps to reduce energy bills. 

Supplied with a 15 metre power cable with plug, 2-pin (Schuko) plug, and internal non return valve.

The Divertron 900X is designed for pumping clean water only. The impeller will be damaged if abrasives and solids are run through it.

The DAB Divertron 900 model has a maximum head of 45 metres or up to 105 litres per minute maximum flow. It comes with an integral mesh strainer to prevent large particles from entering the pump housing, ensuring a longer life. See the technical information for more information on output and the Divertron flow curves.   A pressure vessel will help prevent false re-starts due to small pressure leaks.

It is very safe in an outside submerged application, as the pump is totally water proof (to IP68) This makes it especially safe where children are around - for total peace of mind.

NOTE:  The Divertron pumps MUST NOT sit on the floor of any water tank (they can be suspended using a suitable lifting cable (not supplied)) and MUST be kept within 15o of vertical. They must be run submerged. If run out of the water the motor cannot cool properly. Where using in a Rainwater Harvesting (RWH) tank or shallow tanks where operation may take place in low water level conditions for extended periods, the SteelPumps are worth considering. The SteelPumps can run out of the water, or submerged (to max of 5 m submergence depth). If in any doubt, contact us by email for advice.

Connecting to hoses and pipes

The pump comes with a multi-hose reducer to connect to a garden hose (a stainless steel hose clip is required).

To connect to a 3/4" garden hose simply screw the mulit-hose reducer into the outlet, connect the hose and secure the hose with a stainless steel hose clip.

To connect to a 1" garden hose follow the instructions in the Quick Guide to reduce the height of the multi-hose reducer, connect the hose and secure with a stainless steel hose clip.

If however you intend to connect hard blue or black 32mm MDPE pipe to the pump, you will need a 1" compression adapter (please ensure you select the correct size on the compression adapter page).

Pressure Vessel

We highly recommend you fit a pressure vessel to the water delivery pipework (after the pump). Pressure Vessels help increase the life of your automatic pump when there are leaks in your pipe network/taps. Read more about how Pressure Vessels work.


 Documentation & FAQs

DAB Divertron FAQs and Troubleshooting Guide

Please note: All Divertrons are fitted with a 2-pin (Schuko) plug. We strongly recommend that all submersible pumps are installed on a 10A single fused spur and should be installed by a qualified electrician. If you need an automatic pump with a 3-pin plug, please look at the SteelPumps range.


Guides and ideas

A bit undecided about what options are available to you?

Then have a look at our Rainwater Harvesting FAQs and have a read of our informative guides